Many of you don’t know how To assemble Ryobi table saw? The Ryobi table saw is a beneficial tool for cutting boards. It has a lot of benefits that are described below. These are some facts about the product, along with ways to assemble it correctly.
This article will give you all the information you need to know about this fantastic table saw. If you’re reading, then I guess you’d like to know how to use it as well!
How does the Ryobi Table Saw Work?
The Ryobi table saw works automatically when you press the green “on” button. The machine will start up and begin making your cuts. You must be careful when using this machine, though, or there could be a significant accident.
You’ll need to remember that the parts of the machine will move while it’s working. Your hand could get caught in one of these if you’re not careful, but this is common knowledge when using power equipment like this. Just be sure to stay safe and use your head.
Then you can cut boards into whatever shape or form you want! You can even create angled cuts with this device if you so desire. Let’s say you need to make an angled cut on a piece of wood at 45 degrees exactly; well, just set up the board and press down on the top handle, and it does all the work for you!
How to Assemble Ryobi Table Saw?
The Ryobi table saw is a great machine that can create flawless cuts, but be careful when you’re assembling the blade because it requires a specific way to be done. If you assemble it wrong, it won’t work correctly and could cause injury. So, heed caution!
First off, turn the machine on its side to have access to all of the parts. Look at where the rip fence has been placed and take it out if necessary. When you’re sure that everything else is out of your way, remember the riving knife back into its original position as well as the anti-kickback pawls located behind it.
Then look below those two items, and there should be a black lever called a “riving knife height adjuster.” Pull it up and push down on the riving knife until a click is heard. Then place the anti-kickback pawls back into their original position.
Next, find the white blade guard located just below where you found the height adjuster for the riving knife. Pull it upwards to remove it from over the top of the blade. Then you can proceed to lower down your saw’s splitter/blade guard assembly with one hand so that you have access to tighten or loosen the bolts on either side of both items. Read more here How to change the blade on the roybi table saw.
Now use a wrench or socket set to bolt or unscrew these two pieces together, so they fit tightly in their respective positions underneath the table saw’s metal top. Lastly, place a washer onto each bolt before you finally tighten the pieces together as a whole.
To remove the blade, turn off your machine and allow it to cool down. Once this is done, push in one of the levers found on either side where you inserted the bolt. Both should be located just above the motor housing area on your saw’s top metal surface. You will then have access to lift or lower down a heavy-duty metal cover that protects its blade from damage by objects flying into it during operation.
This is very important because you don’t want any harm coming to you or anyone else, so take these precautions seriously! After this, find where the riving knife height adjuster is placed and pull it up onto its original before replacing your saw’s splitter assembly and blade guard. Finally, follow the steps in reverse to reattach your metal top cover, and you’re almost done with this process!
You can now place any leftover/unused tools back into their rightful place. Reattach the rip fence using the two screws located just below it on each side of where its throat plate is placed. Lastly, place the cast-iron tabletop back down onto the saw’s metal top and tighten it in place using its four screws on all corners of where you inserted it.
First, make sure that your machine is turned off! The next step requires you to take a hex key wrench and remove the remaining bolts from either side of your blade’s arbor housing. Now place the wrench around your blade’s arbor nut and turn it counter-clockwise so that it is loosened. Then you can pull the blade off of its shaft by hand or use a pair of pliers to grip onto it firmly, then pull up with steady force until it comes loose from its socket.
Tricks and Tips:
-
It would be best if you found the documentation that came with your Ryobi table saw, it will include an exploded view of the table saw with all parts labeled. You can use this diagram as a reference. This is very important – without these instructions, you may not be able to put the item together correctly and safely! Read more here How to align a table saw blade.
The first step in assembling a Ryobi Table Saw is removing all pieces from their respective boxes. Make sure to take inventory of all items included in the package before using or discarding any boxes or packaging materials.
Now place your tabletop on its side so that it looks like a ramp. Place one leg at each end of the tabletop on top of the corresponding leg stands. -
Now you need to take the two long metal beams with plastic clips and slide them into the openings on either end of your tabletop. You can use a little bit of force for this, but be careful not to break the clips or scratch your tabletop with the metal parts, as this could damage it in the future!
After inserting both beams fully, place one hand underneath each leg stand and tip up so that it rests against the edge of your tabletop. Again, this step takes some force and care must be taken in order to avoid scratching or damaging any materials.
Once all three stands are resting securely on the beams do not lift your table by its legs yet! First, we will install another piece. -
Fold up one of the caster wheels so that it is pointing skyward and place it onto the end of its corresponding crossbeam protruding from below your tabletop. Make sure to choose the correct side as there are two beams and two caster wheels! Do not forget this or you may end up with a wobbly table! Next, turn the caster wheel down and let go; now take another long metal beam (the same ones as those used in step 2), slide them into the holes on either end of your tabletop, making sure they look like they match up with those sticking out from under your table.
After inserting both beams fully, place one hand underneath each leg stand and tip up so that it rests against the edge of your tabletop. Again, this step takes some force and care must be taken in order to avoid scratching or damaging any materials. -
Now pick up one end of your saw blade while holding onto to the part sticking out from underneath your tabletop, pull it towards you until it extends across the table, then lower the end into its corresponding leg stand. Your saw should now look like a giant letter ‘T’. You can tip one side down slightly so that it is easier to get all legs properly placed on top of their corresponding beams. Do not raise your table yet! Ensure all stands are secure to their beams before continuing! Repeat for remaining leg stand with remaining saw blade part. Make sure you have both saw blades fully extended before proceeding!
If you’re having trouble getting some of the legs to fit on top of their respective beams, simply take the saw blade out and try again. -
Now that all legs are resting securely on top of their corresponding beams, lift your table up with one hand while holding onto both saw blades with the other. Make sure they don’t knock into each other! Next place two more beams coming from underneath your tabletop between each leg stand – one at a time. This is where it gets tricky! NOTE: We will NOT put screws into these parts yet. They are just being held in place by gravity so that we don’t have any major accidents while putting our screws in! After you set down your saw, make sure all four beams are in place between each leg stand before continuing.
-
Now that the base of our table is complete, we can attach both saw blades to their motors. We will do this by screwing the blade underneath the tabletop into its motor (one at a time), while another person holds the saw motor in place. Remember to use a flat head screwdriver! Do this for both blades, BUT do not attach the motor on top of the tabletop yet!
-
Now that we’ve attached one blade and its corresponding motor underneath the table, we can start attaching our motors to our tabletop. Using two long flat head screws, place one on either side of the motor home in your tabletop. Do this for both motors, but before you tighten them down completely, make sure that when you turn your saw blade it spins freely – you may need to readjust a few things!
-
Your tabletop should be ready for use once all 4 screws are installed and your blade spins easily. For the next steps, you will need an extra set of hands to hold your tabletop up! Read more here How to install blade guard on roybi table saw.
-
It’s finally time to attach our saw tabletops! Grab one end and tip it up on its side so that it is more stable for the person holding it – then have them carefully lower it into place. Your saw should now look like the shape of a giant letter ‘T’.
Features:
- The Ryobi table saw is a great machine that can create flawless cuts.
- You will then have access to lift up or lower down a heavy-duty metal cover that protects its blade from damage by objects flying into it during operation.
- First, make sure that your machine is turned off! Then you can proceed to lower down your saw’s splitter/blade guard assembly with one hand so that you have access to tighten or loosen the bolts on either side of both items.
- Lastly, place the cast-iron tabletop back down onto the saw’s metal top and tighten it in place using its four screws on all corners of where you inserted it.
Conclusion
Ryobi table saw is the perfect tool for cutting boards. It is very helpful and has a lot of benefits that are described below. These are some facts about the product along with ways to assemble it correctly. This article will give you all the information you need to know about this fantastic table saw. If you’re reading, then I guess you’d like to know how to use it as well!
Comments are closed.