How To Build A Table Saw Fence?

If you’re a woodworker or even a do-it-yourselfer, then you know that one of the essential pieces of equipment in your workshop is the table saw. And if you want to get the most out of your table saw, you need to have a good fence.

Now we come to the critical question: how do you build a table saw fence? It’s not as difficult as it might seem. In this article, we’ll show you how to do it.

What Is A Table Saw Fence?

A table saw fence is a critical piece of equipment for any woodworker. It’s a rail system that runs parallel to the blade of the table saw, and it allows you to guide your workpiece through the saw blade securely. A good fence is essential for ensuring accurate cuts.

Why Should You Use a Table Saw Fence?

There are a few reasons why you should always use a table saw fence:

  • Accuracy – A good fence ensures that your cuts are accurate.
  • Safety – A fence helps keep your hands away from the blade, which reduces the risk of injury.
  • Convenience – By using a fence, you can quickly

How To Build A Table Saw Fence? ( Step by Step Process )

Building a table saw fence is not a difficult task, but it does require some basic carpentry skills. Here’s how to do it:

Step 1: Gather All the Necessary Tools

Before you can build a table saw fence, you’ll need to gather all the necessary tools and materials. Here’s what you’ll need:
2×4 (longer than the depth of your table saw)- 1 pc
4 piece Wood screws-(3″ deck screws)
A Jigsaw
A Tape measure
Screw-threaded rod with nut

Step 2: Measure the Table Dimension

The first step is to measure the dimensions of your table saw. You’ll need to know the width and depth of the table, as well as the distance between the blade and the fence.

Once you have measured these dimensions, you can use them to build your fence.

Next, you’ll need to cut the 2×4 board to the correct size. The length of the board should be equal to the depth of your table saw, plus 1 inch.

Width-wise, the board should be 2 inches narrower than the width of your table saw.

Once you have cut the board to size, it’s time to start building the fence.

Step 3: Assemble the Fence Rail

The fence rail is the backbone of the fence, and it needs to be sturdy and reliable. So, take your screw-threaded rod and nut and thread them onto one end of the board. This will serve as the mounting point for the rail.

Now, using your jigsaw, cut two notches on the board, as shown in the diagram below. Ensure that the notches are big enough to fit the rod and nut.

Once you have cut the notches, use your wood screws to attach the rail to the board. Make sure that the screws are countersunk so that they don’t protrude from the board’s surface.

Step 4: Mount the Rail to the Table Saw

Now it’s time to mount the rail to the table saw. This is a straightforward process, but you’ll need to be careful and precise.

First, measure and mark the position of the rail on the table saw. Next, use your drill to make a pilot hole in the table saw. Then, use your screwdriver to insert the screws into the pilot holes. Finally, tighten the screws with your wrench.

Step 5: Tightly Screw the Fence

Now it’s time to tighten the fence to the rail. This is an important step, so take your time and be careful.

First, use a screwdriver to loosen the screws on the fence. Next, use your wrench to tighten the screws on the rail. Finally, use your screwdriver to re-tighten

And you’re done! Your table saw fence is now complete. Enjoy!

So, there you have it: a simple guide on how to build a table saw fence. It’s not difficult, but it does require some basic carpentry skills. So, if you’re looking for a new fence for your table saw, or if you want to learn how to build one yourself, then this guide is for you.

A video guide on how to build a table saw fence.

FAQs:

What Side Of The Table Saw Should The Fence Be On?

The fence should be on the same side as the blade. This will ensure that the fence is parallel to the blade, essential for accurate cuts.

How Far Away From The Blade Should The Fence Be?

The fence should be a few inches away from the blade. If it’s too close, then you run the risk of getting your fingers caught in between the blade and the fence. If it’s too far away, you won’t be able to make accurate cuts.

Can I Make Cuts perpendicular To The Blade?

You can make cuts perpendicular to the blade by using the miter gauge slots on the table saw. Just make sure that the fence is parallel to the blade.

Can I Make Cuts At An Angle?

Yes, you can make cuts at an angle by using the miter gauge slots on the table saw. Just make sure that the fence is parallel to the blade.

Conclusion:

Building a table saw fence is not difficult, but it does require some basic carpentry skills. If you’re looking for a new fence for your table, saw, or if you want to learn how to build one yourself, then this guide is for you. Thanks for reading!

So, there you have it: a simple guide on how to build a table saw fence?. It’s not difficult, but it does require some basic carpentry skills. If you’re looking for a new fence for your table saw or want to learn how to build one yourself, then this guide is for you. Thanks for reading!