Do you have a Dewalt reciprocating saw that needs to be cleaned?
I do, and I know how frustrating it can be when the saw isn’t performing at its best. That’s why I’m going to show you how to clean your Dewalt reciprocating saw in just a few minutes so it’s running like new again.
You’ll be able to get through your projects faster and with less frustration when your saw is clean and functioning properly. Plus, you’ll extend the life of your saw by taking care of it regularly. Follow these simple steps and you’ll be good to go!
How to clean Dewalt reciprocating saw | Step by Step Guide:
Here are some steps to clean you saw:
Cleaning the blade:
Cleaning the blade is perhaps the most important part of cleaning a Dewalt reciprocating saw. If you’ve ever gotten anything stuck in the teeth of your reciprocating saw, then you know that it’s necessary to clean them thoroughly after each use. You can do this by hand or with an automatic blade cleaner (which has rotating brushes). Either way, be sure to brush away any debris and wipe down the blade with a dry cloth.
What about other parts of my Dewalt reciprocating saw?
After you clean the blade, you can use a small amount of light machine oil or lubricating oil to remove any built-up grime on the outside of your tool. If it has been particularly dirty, then consider using paint thinner to break through tough grease. Finally, if there are any loose parts inside the housing, tighten them by hand so they don’t fall off during operation.
Cleaning the Motor:
You shouldn’t have to clean the motor of your Dewalt reciprocating saw on a daily basis. However, if you notice that it is heating up after extended use or smells funny, then it’s time for deeper cleaning. Begin by disconnecting the power source and removing the blade guard. After that, spray compressed air into all intakes and exhausts on the blade housing until they are free of debris.
Finally, remove any grime with paint thinner on a soft cloth or brush using light machine oil as needed. You can also take off each attachment piece of your Dewalt reciprocating saw (i.e., blades, blades guards) so you can individually hand wash them with warm water, soap, and a sponge to ensure thorough cleaning.
How to clean the housing of a Dewalt reciprocating saw?
After you clean your Dewalt reciprocating saw’s blade, it’s time to clean the outside of the housing. You can clean off any stubborn dirt or grime with paint thinner on a soft cloth. If your tool is an older model that uses oil instead of grease (and therefore has more built-up grime), then you can use paint thinner with light machine oil as an effective solvent.
If there are any bolts or screws loose inside the housing, tighten them by hand before using your Dewalt reciprocating saw again.
Why does my Dewalt reciprocating saw smell bad?
If cleaning the motor and other parts of your Dewalt reciprocating saw didn’t fix its smelly problem, then there could be an oil leak in either the blade housing or the motor area. If you notice any leaking fluids, then be sure to clean them up before using your Dewalt reciprocating saw again.
Does that pretty much cover it?
Yes! Completing these steps should have your Dewalt reciprocating saw looking and smelling like new, so you can get back to work with minimal wait time. Our tools are an important part of our livelihood, so learning how to clean a Dewalt reciprocating saw is one of the most valuable skills for homeowners and contractors alike.
Useful tips on things I didn’t know about my Dewalt reciprocal saw
It’s okay to use WD 40 on electric power tools but it shouldn’t be used on the internal parts of the motor.
The best oil for your saw is light machine oil, which can be found at any hardware store.
If you are using a reciprocating saw without a blade guard, make sure to wear safety goggles or glasses at all times!
You should never hold your hand near or directly in front of the reciprocating saw when it’s running. Always keep your hands behind the tool and away from its moving parts.
How to lubricate the moving parts of a Dewalt reciprocating saw?
There are a few different ways to keep the reciprocating saw’s moving parts well-lubricated. The first is to add light machine oil, which can be found at any hardware store. Another way is to spray some WD 40 on the housing of your Dewalt recprocating saw then wipe it down with a soft cloth (make sure not to get it in the motor area). If you notice that there is too much build-up on your blade, you can try using paint thinner and some light machine oil instead.
Safety Precautions
- Keep your hands behind the blade at all times.
- Do not point it toward anyone around you, including yourself.
- Always wear safety glasses or goggles when using a reciprocating saw.
How do I sharpen the teeth on my Dewalt saw?
If you didn’t notice any signs of a blade becoming dull, then you can sharpen the teeth with a file or a grinder. Use a steady up and down motion as you move along the entire length of your Dewalt reciprocal saw’s blade.
What is the best oil for my DeWALT reciprocating saw?
The best oil to use for your DeWALT reciprocal saw’s motor is light machine oil, which can be found at any hardware store. However, if your reciprocating saw uses separate oil for its motor instead of grease, then you can use coating or sewing machine oil.
Conclusion
Dewalt reciprocating saws are a popular choice for DIYers and professionals alike. They’re durable, efficient, and can handle a wide variety of cutting tasks. However, like any other piece of equipment, they need to be cleaned properly in order to maintain their performance and lifespan. In this article, I’ve outlined the steps you need to take to clean your Dewalt reciprocating saw safely and effectively.