How To Grease A Dewalt Type 2 Reciprocating Saw | The Ultimate Guide

Greasing your power tools from time to time is a very necessary step to keep them in top shape and extend their working lifespan. Without proper lubrication, it will wear down fast, and cause friction between moving parts that can reduce its power or stop it from working completely.

DeWalt makes some of the best reciprocating saws on the market, and proper lubrication is key to getting the most out of them. In this blog post, I’ll show you how to grease a DeWalt Type 2 reciprocating saw. This easy maintenance task will help keep your saw running like new for years to come. So let’s get started!

What You Will Need

To grease your reciprocating saw, you’ll need a few simple things. These are all available at the hardware store or any home improvement center. You can also buy it from online stores like The Home Depot, Amazon, etc.

  • A Syringe or Hand Pump (to put grease in grease fitting of saw) (Recommended CLENZOIL)
  • Silicone-based lubricant (comes in an aerosol can)

What Type of Grease Should I Use?

The best type of grease for the job is a silicone-based lubricant, which is what most manufacturers recommend using. It’s quite literally made out of oil with some thickening agents mixed in to make it easier to work with. This makes it very useful because when it reaches the gears and starts to melt, all that needs to be done is mix it up until it’s evenly distributed throughout. Best recommended grease Permatex 22058.

How To Grease A Dewalt Type 2 Reciprocating Saw

Now that I have the tools and materials needed, let’s go ahead and get busy! This task will take about 10 minutes to complete. Keep in mind that if you don’t have a grease fitting on your tool, this method probably won’t work for you. You’ll instead need to speak with a service center or an authorized repair shop to get it done for you. The steps are broken down below:

Step 1: Locate The Grease Fitting

In order to add grease to the reciprocating saw, we first need access to the inside of its gearbox. With most models, there will be three screws holding each side of the casing together and they need to be removed. It’s important that you set these screws aside in a safe place because they will not fit anywhere else and you’ll need them again later. The bottom plate of the casing should now come right off if it isn’t already loose. Set it aside as well for now.

Step 2: Prepare the Gearbox

With the gearbox exposed, we’re ready to prepare it for filling up with grease. There’s a small metal bar located inside and this needs to be removed before we can do anything further (it also shouldn’t be left behind and should be kept safe). There are only two bolts holding this part in place; one on each side, near where the motor meets the body of the tool. Remove those bolts and the bar should slide right out.

Step 3: Grease The Gears

Now that we can access the gears, it’s time to get them thoroughly covered in lubricant. This step is vital because this kind of maintenance helps prevent major problems from occurring down the line such as overheating and seizing up for good. Fill up a small syringe or hand pump with some lubricant and start pumping it into the hole where you removed the metal bar earlier.

Also, make sure to fill up both sides evenly and until they’re overflowing with grease (the instructions will tell you how much). It should be about halfway full before stopping. Once you’ve expended all your oil, put that metal bar back where it came from, and then secure it down with those two bolts you took out earlier.

Step 4: Reassemble the Saw

In order to reassemble everything, it’s as simple as doing everything backward. In other words, put the casing back together and secure it down with those three screws. Slide the bar we removed into its respective spot and then go ahead and reconnect the motor by attaching all of its cables and wires back onto where they came from. The casing should come apart just like every other toolbox on the market so don’t worry about any special steps that might be different than what you’re normally used to seeing/doing.

Simple Guide on How To Grease A Dewalt Type 2 Reciprocating Saw

Tips For Greasing A Reciprocating Saw

Here are some tips for those of you who are either new to this kind of repair or who might not know as much as they should:

  • Before doing anything else, make sure that the reciprocating saw is turned off and unplugged from where it’s connected. The last thing anyone wants is for something to go wrong while working.
  • Always read all instructions before starting work on any power tool. This way there are no surprises later down the line if something unexpected happens after getting everything done.
  • If your reciprocating saw does not have a grease fitting, you will need to take it to a service center or authorized repair shop to have the grease added. You can even take it to a local repairing workshop for greasing.
  • Make sure the reciprocating saw is turned off and unplugged before starting the greasing process.
  • Fill up a small syringe or hand pump with lubricant and start pumping it into the hole where you removed the metal bar earlier.
  • Once you’ve expended all your oil, put that metal bar back where it came from, and then secure it down with those two bolts you took out earlier.
  • Reassemble everything backward and you’re done!

Conclusion

It’s important to do this kind of maintenance regularly (if not yearly) on your power tools, especially if you’re using them frequently. This short guide should have explained the steps about how To Grease A Dewalt Type 2 Reciprocating Saw and helped prevent future malfunctions or issues that might be hard to solve later on down the line.

FAQs

Q: What exactly is grease?

A: Think of grease as being similar to soap except thicker, slicker, and able to keep working longer under tough conditions (e.g., high heat). Grease also fills gaps which keeps components from wearing down too fast over time.

Q: How Often Should This Be Done?

A: This will depend on how often you use your reciprocating saw, whether or not it’s running under high pressure, and what kind of conditions it’s being used in. Replacing the grease once a year is great if you’re using this tool every week to cut through tough materials like steel.

Q: Where Can I Get The Right Kind of Grease?

A: This kind of lubrication can be found at hardware stores or your local automotive shop. You can also purchase it over the Internet, but make sure you know exactly what kind of grease to get (this is usually written on the reciprocating saw itself).

Q: How do you lubricate a saw blade?

A: To lubricate a saw blade, you have to remove the entire blade from your tool’s body and then sprinkle some of the lubricants onto it. Afterward, slide the blade back in and secure it down with a bolt or screw so that it stays in place while you’re working on something else. Best DEWALT Reciprocating Saw Blades 6-Piece (DW4856).

Q: What do I do if my saw won’t cut anymore?

A: Have someone hold down the trigger while you look at one of the blades to see if there’s something stuck inside that might be jamming everything up (e.g., rocks). If that doesn’t work try using another blade because there might be something wrong with the current one.

Q: Is This A Dangerous Operation?

A: Similar to any kind of work involving machinery, it’s important to always make sure your reciprocating saw is turned off and unplugged before starting the process. And lastly, never attempt this on a tool you don’t know how to use since improper handling could lead to serious injuries.