Installing a blade guard on your Craftsman table saw is an important safety precaution. This video will show you how to do it quickly and easily.
A properly installed blade guard protects your fingers and hands from being injured by the spinning blade. It’s a simple process, and this article will take you through it step-by-step.
You’ll be able to complete the installation in just a few minutes, and then you’ll be able to use your table saw with peace of mind, knowing that your fingers are safe from harm.
How To Install Blade Guard On Craftsman Table Saw? – Step By Step
Here are some steps to install a blade guard on your Craftsman table saw.
- Unplug the saw from the power source.
- Remove the throat plate by unscrewing the two screws that hold it in place.
- Raise the blade to its maximum height.
- Install the blade guard by first attaching the bracket to the back of the table saw (underneath the tabletop). Then, slide the guard onto the bracket. I Use Craftsman 089037007700 Blade Guard.
- Screw the bracket into place using the two screws that were removed in Step 2.
- Replace the throat plate and screw it into place.
- Plug the saw back in and test the blade guard by moving it up and down to make sure it is secure.
What Is The Purpose Of A Blade Guard?
The primary reason for the blade guard is to prevent the user from accidentally cutting themselves. This can be done in several ways, including by making it difficult or impossible to reach the edge of the knife.
The second most important function of a blade guard is to keep debris out of the knife’s handle and/or mechanism. A guard that is designed well will also provide a place to rest your hand while using the knife.
There are other reasons why you might want a blade guard. For example, some people like to use their knives as eating utensils. If the guard gets in the way of this, they may not use the knife at all.
Other people just don’t like working with sharp blades near them. They prefer to work with dulled blades instead. Some people feel safer working with a guard in place. Others do not. To each his own.
Safety Tips
Cutting with the wrong tool can cause serious injury. This includes using a circular saw when a jigsaw is more appropriate. A circular saw is used for ripping lumber, not cutting across the grain. Always use the correct tool for the job.
Use an anti-kickback pawl whenever possible. Anti-kickback pawls are found on most power miter saws. These devices help reduce kickbacks. Kickbacks occur when the spinning blade hits something in its path as it moves away from the workpiece.
The force of the blade striking the object causes the blade to spin back toward the operator. An anti-kickback pawll prevents this action.
- The first step to safely using a table saw is to set up the machine correctly. Make sure all parts are properly aligned before turning the motor on.
- Place a piece of scrap material against the fence so that the blade will have a clear path to travel through. Before beginning any cuts, make sure the blade is free of obstructions.
- Make sure the blade guard is in place. It may be attached permanently or removable. Either way, it’s best to use a blade guard because it reduces the risk of eye injury.
- Attach the blade guard to the side of the table saw. You can either screw it into position or bolt it down.
- Turn on the motor and adjust the height of the blade guard. Adjusting the height allows you to raise or lower the guard without having to remove it.
- Adjust the angle of the blade guard. Angle the guard slightly forward or backward depending on where you plan to make the cut. For example, if you’re making a horizontal cut, the guard should be angled slightly forward.
- Turn off the motor and test the blade guard. Check to see if there are any loose pieces. Also check to see if the blade guard has moved out of the desired location. If necessary, tighten bolts and screws.
If you’ve installed a permanent blade guard, clean it regularly. Otherwise, wipe it down occasionally.
Conclusion
A blade guard helps prevent injuries caused by flying objects. However, you must take precautions to ensure that the blade stays securely fastened to the saw. Follow the steps above when setting up your table saw.
FAQ,s
How does a blade guard work?
Blade guards are usually made of metal, plastic, or wood. Metal guards are typically used for industrial applications.
Plastic guards are generally cheaper than metal ones but tend to break more easily. Wood guards are often less expensive than other types of guards. Wood guards come in many different shapes and sizes.
One common type of wood guard is called a “fence.” Fences are designed to hold the blade in place during operation. Another popular type of guard is called a “pawl”.
What is the largest blade that can go on the saw?
There are two sizes of blades: 12″ and 14″. The smaller size is usually used for trimming small items while the larger size is used for heavy-duty applications such as framing.
Splinters are created when wood particles get caught between the teeth of the blade and the fence. To avoid splintering, make sure the fence is parallel to the blade.
Also, try to cut straight lines. If you need to cut curves, use a router instead. Best Large Blade 14BLADEST.
Why does my table saw not have an auto-stop mechanism?
Most newer table saws do not include an auto-stop function. Instead, they have a safety device called a brake system. This feature automatically stops the blade when it encounters an obstruction.
If you’re finishing a piece of wood and it looks like there are still some parts left, what happens next?
When you finish cutting a piece of wood, you’ll notice that there are still some remaining parts left. When the saw is finished cutting, the last part of the piece remains stationary.
The rest of the piece continues moving past the blade, which creates a ragged edge.