How To Make a Circular Saw Into a Table Saw? – Expert Guide

Circular saws are very versatile tools and can be used for a variety of tasks around the house. We’ll show you how to make a circular saw into a table saw.

What would you say if I told you that you can turn a circular saw into a tabletop saw without spending too much money or having to go through a lot of hassle? Well, it’s true. All you need to do is get a couple of old hand tools from your garage and some wood scraps. And that’s exactly what we did.

Tabletop saws are great because they allow you to cut large sheets of plywood and other materials. They also come in handy when cutting smaller pieces of wood such as moldings, picture frames, and furniture parts.

However, these machines aren’t cheap. In fact, they can cost anywhere between $100 to $1,500 depending on the model. If you want to save money, you can build your own tabletop saw using common household items.

How to make a circular saw into a table saw Step by Step guide

I recently purchased a circular saw to use for cutting wood. I was surprised to find out that it didn’t come with a blade guard.
I searched online for information about converting a circular saw into a table saw, and found some useful tips.

  1. Take a piece of wood about 2 inches thick.Cut two pieces of wood about 6 inches long and 4 inches wide.Use a saw or jigsaw to cut these pieces into four equal parts.

  2. Place one of the six pieces of wood onto a flat surface.Make sure the edges of the wood are flush against each other.

  3. Put a level across the top edge of the board.This helps ensure the table is perfectly straight.

  4. Measure out 12 inches along the length of the board.Mark the center point of the board.

  5. Using a pencil, draw a line connecting the center points of the boards.

  6. Draw another line perpendicular to the first line.

  7. Repeat steps 4 through 6 until you reach the desired height of the table.

  8. Using a drill press, drill holes into the ends of the boards.Drill three evenly spaced holes into each side of the board.Drill two holes into the center of each board.

Safety Tips

  • Make sure the blade guard is properly attached to the table saw.
  • Always wear eye protection when working with a table saw.
  • Never use a circular saw to cut through concrete or masonry.
  • Use a straightedge to guide the blade when cutting metal.
  • Be careful when changing blades.
  • Never run a circular saw while holding anything over 6 inches wide.
  • When cutting large pieces of wood, use a table saw instead of a circular saw.
  • Avoid using a table saw if you are tired or stressed out.
  • Don’t try to finish a project with a table saw alone. You can finish the project with a table saw instead.
  • Don’t forget about safety when using a table saw. Follow these safety tips to avoid accidents.

Mistakes to avoid while using a table saw

Table saws are one of the most dangerous tools in the workshop. They are used for cutting wood, metal, and plastic. They are heavy and powerful machines that can cause serious injuries if not handled properly. A table saw is a great tool for DIYers who enjoy working with wood. However, there are certain mistakes that people make while using these tools.

Here are some of the most common mistakes made while using a table saw.

1. Improperly positioning the blade guard

If you don’t use the proper blade guard, you could get injured. Always remember that the blade guard protects you from the blade’s rotating parts. It helps prevent accidental contact with the spinning blade. But if you forget to remove the blade guard, you could be seriously hurt. So, always position the blade guard correctly before starting to cut.

2. Not keeping the blade sharp

When the blade gets dull, it becomes unsafeSharp blades are essential for safe operation.Keep your blade sharp by using a sharpening stone.Use a fine grit stone to sharpen the teeth of the blade.Do not use coarse grit stones.

3. Using an incorrect blade size

Using the wrong blade size can lead to accidents.Never use a blade that is too small or too large for the job.

4. Forgetting to change out the blade

Changing out the blade after every cut is very important.This prevents damage to the blade and ensures safety.

5. Cutting off the tip of the blade

Cutting off the tip of the saw blade can result in injury.Always remember to replace the blade.

6. Operating the machine without a dust collector

Dust collectors collect dust particles generated by the saw blade.These particles can accumulate over time and pose health risks.

 

FAQ’s

Why making a table saw from a circular saw is dangerous?

Circular saws are designed to cut wood only.However, they have been modified to cut other materials like steel and aluminum.As such, they are more likely to injure you than a regular table saw.

Can I use a circular saw to make my own table saw?

Yes! A circular saw can be converted into a table saw.

What are the advantages of making a table saw from a circular saw?

Making a table saw from a circle saw gives us several benefits.
First, it saves space.
Second, it’s easy to transport.
Third, it’s cheaper.

Table Saw vs Circular Saw Do You Need Both?

You may wonder why do we need both a table saw and a circular saw.Well, a table saw is best suited for tasks where a lot of material needs to be cut at once.For example, cutting a piece of plywood requires a lot of force.And this kind of work can be done faster with a table saw.On the other hand, a circular saw is better suited for jobs that require precision cuts.Such as cutting a hole or creating a groove.In addition, a circular saw is easier to control because the blade rotates around a fixed axis.Therefore, you can easily adjust the depth of the cut.You can also adjust the angle of the cut depending on what you want to achieve.A circular saw is also safer because there are no moving parts.

Conclusion

The table saw has become indispensable in our daily life. However, due to its power and versatility, it poses many dangers. We will show you how to make a circular saw into a table saw.