Scroll saw tables can be a little tricky to get just right. Here’s how to make your harbor freight scroll saw table flat and ready for woodworking. By following these simple steps, you’ll have your table perfectly aligned and ready to go in no time! With a smooth, flat surface, your projects will come out looking great – no more crooked cuts or uneven surfaces. Let’s get started!
Some Important Steps to Keep in Mind
Aligning the Table
The first step is to align the table. This can be done with a straight edge and a level. Place the straight edge across the table and adjust the leveling screws until the table is perfectly flat. Make sure to check both the front and back of the table, as well as each side.
Attaching the Fence
The fence is what you use to guide your cuts. It’s important that the fence is straight and parallel to the table, so it’s important to attach it correctly. The easiest way to do this is to clamp the fence in place and then screw it down. Make sure that the screws are short enough that they won’t interfere with the blade.
Adjusting the Blade
Now that the table is aligned and the fence is in place, it’s time to adjust the blade. This can be done by loosening the screws on the side of the table. Be very careful when doing this, as the blade is sharp and could easily cut you. Make sure to keep your hands and fingers well away from the blade. Once the screws are loose, you can adjust the height of the blade by moving it up or down. You can also adjust the angle of the blade by turning it on its side. Be sure to tighten the screws back up when you’re finished adjusting the blade.
Benefits
Making a harbor freight scroll saw table flat has several benefits. It can make the saw more accurate and help to prevent blade binding. It can also make the saw easier to use and improve the quality of the cuts that are made.
How to Make a Harbor Freight Scroll Saw Table Flat?
There are a few methods that can be used to make a harbor freight scroll saw table flat. The most common method is to use an angle finder to find the angle of the table and then adjust it accordingly. Another method is to use shims to level the table.
Angle Finder:
The easiest way to make a harbor freight scroll saw table flat is by using an angle finder. This tool allows you to find the angle of the table and then adjust it accordingly. To use the angle finder, first measure the height of the table at each corner. Next, find the angle of the table by using the angle finder to match the height measurements to the angles on the tool. Finally, use a screwdriver or wrench to adjust the angle of the table.
Shims:
If an angle finder is not available, another way to make a harbor freight scroll saw table flat is by using shims. Shims are thin pieces of metal or plastic that can be used to level surfaces. They can be purchased at most hardware stores or online. First, measure the height of the table at each corner. Next, use a ruler to find the difference in height between the corners. Finally, place shims under the table legs until the table is level. Both methods described above can be used to make a harbor freight scroll saw table flat. However, it is important to note that these methods may not work on all saws. If the angle or height of the table cannot be adjusted, then these methods will not work.
Additionally, if the saw has a tilting blade, it is important to ensure that the table is parallel with the blade before making any adjustments. Making a harbor freight scroll saw table flat can help to improve the accuracy and quality of your cuts. It can also help to prevent blade binding and make the saw easier to use. By using an angle finder or shims, you can easily adjust the table to ensure that it is level and parallel with the blade.
Safety Precautions
When using any power tool, it is important to take the necessary safety precautions to prevent injury. With a scroll saw, this includes wearing goggles to protect your eyes and using a dust mask to avoid breathing in the sawdust. Additionally, it is important to make sure the table on which the scroll saw is mounted is flat. A warped or uneven table can cause the blade to bind and kick back, potentially causing injury. You can check the flatness of your table by measuring the distance between two points on its surface. If these points measure more than 0.003 inches apart, your table is not flat and should be corrected.
One way to correct an uneven table is to use shims. Shims are thin pieces of material that can be inserted under the table legs to level it out. You can buy shims at most hardware stores, or you can make your own from cardboard or other thin materials. Another way to correct an uneven table is to use a leveling compound. This is a liquid substance that can be poured over the table surface and will help to create a flat surface. There are many different types of leveling compounds available, so be sure to read the instructions carefully before using one.
Once your table is flat, it is important to keep it that way. To do this, periodically check the surface for any bumps or irregularities and adjust them as necessary. Also, make sure the screws that hold the table in place are tight so that the table does not move around. By following these safety precautions and taking the necessary steps to ensure a flat table surface, you can use your scroll saw safely and effectively.
Conclusion
After completing the Harbor Freight scroll saw table build, it was important to make sure that it was flat. This could be done by using a straight edge and checking for any high or low spots on the tabletop. If there were any areas that needed to be corrected, they could easily be fixed with a belt sander. By following these simple steps, anyone can have a scroll saw table that is ready for use right out of the box. Have you tried making your own scroll saw table? What tips would you add? Let us know in the comments below.