Do you know that it’s important to oil the blade after every use? This keeps your blade sharp and in good condition. If done correctly, this will ensure a smooth cut every time while also extending the life of your blades significantly. But how to oil reciprocating saw?
In general, to oil, your reciprocating saw, Remove the blade from the saw. Then clean off any old oil and dirt from the saw with a clean cloth. Next, apply a few drops of new oil to the moving parts of the saw. Finally, reattach the blade to the saw.
Keep reading to learn more about tips and frequently asked questions by most users.
Why You Should Oil Reciprocating Saw
Let’s start with why you should oil a reciprocating saw. As mentioned earlier, this will ensure a smooth cut every time which is important if you want clean and precise cuts when doing your projects around the house or office. I personally Use ATOMIC reciprocating saw for DIY projects
It also helps keep your blade sharp and in good condition. If you do it regularly, then this will extend the life of your blades significantly and these replacement costs can add up over time.
What Type Of Oil You Should Use For Reciprocating Saw
In the past, most people used WD-40 oil for saws but according to most users online, this is not a good choice. The reason why is that it doesn’t last long and coats the blade with a thin layer of oil which can cause rust. Instead, you should use an SAE 5w-20 Oil instead.
Also, make sure that whatever you choose is lightweight and meant for auto engines. This isn’t only because the saws are powered by gas but because it’s thin enough to penetrate through even tight spaces where other thicker oils cannot go through.
How To Oil Reciprocating Saw
Here is a detailed guide for oiling a reciprocating saw. If you want to know how to oil reciprocating saw. Keep reading to learn the step-by-step process.
Step 1
Make sure that your blade is not running at extreme speeds. This is important because if it’s moving too fast, the oil will get flung off and burn your skin if it comes in contact with your hand or eyes.
Step 2
Take a few minutes of time out to clean any debris from the blades’ teeth using an air compressor or canned compressed air. This will ensure that all parts of the blade are well lubricated which leads us into our next step.
Step 3
Now that all parts of your reciprocating saw are free from dirt and debris, you can now apply oil to its different parts. For this, we recommend using a spray aerosol oil for fast and direct application.
Step 4
Cover all pivot points as well as the inside of the blade’s base and rubber grips since these tend to attract dust and debris easily. Always remember that you need to give an ample amount of time for the oil to penetrate into the metal.
Step 5
Clean oil from your blade using a rag or paper towel and then open the storage case to remove it.
Step 6
To clean it up completely, you can also use a hose or power washer to make sure that all oil is washed off.
You are now done oiling your reciprocating saw. To confirm that you have used the right amount of oil or not, test it out by running it through a piece of scrap wood first before doing your projects around the house.
How Often You Should Oil Reciprocating Saw
According to most users online, you should oil your reciprocating saw at least once a month for optimum performance. However, the frequency of oiling your saw will depend on several variables such as working conditions, usage, storage, and how often you use it. That is why some users online recommend changing the oil every time after using it.
Tips For Oiling A Reciprocating Saw
- Make sure that the blade is not running at extreme speeds before oiling it. This is to prevent the oil from getting flung off and burning your skin if it comes in contact with your hand or eyes.
- Clean any debris from the blades’ teeth using an air compressor or canned compressed air before applying oil. This will ensure that all parts of the blade are well lubricated.
- Apply oil to its different parts using a spray aerosol oil for fast and direct application.
- Cover all pivot points as well as the inside of the blade’s base and rubber grips since these tend to attract dust and debris easily. Always remember that you need to
Conclusion
That’s it, you now know how to oil a reciprocating saw and the proper technique for doing so. Oil lubricates your reciprocating saw so as to keep it functioning smoothly and prevent rusting as well as extending its life.
No matter what type of oil you use for your reciprocating saw, always remember to wipe off excess oil from it using a rag or paper towel and then store it properly after each use. I hope that this article has helped you learn how to properly oil a reciprocating saw. If you have any questions about oiling a reciprocating saw, please feel free to leave them in the comment below.
FAQs
Q: What type of oil should I use?
A: I recommend using SAE 10 or 20 oil which is lightweight and meant for auto engines since this will not only last longer but can also penetrate into tighter spaces in the blade (where WD-40 cannot).
Q: Can I Use WD-40 On My Saws?
A: No, never use WD-40 on your blades since this can cause rust and is likely to burn your skin if it comes in contact with it. Instead, always choose an SAE 10 or 20 oil instead, which are thinner oils good for auto engines.
Q: How often should I oil my reciprocating saw?
A: Most users online suggest doing this at least three times per year and some even recommend doing it more than once every month. This will keep your blades in good condition and working efficiently for many years of usage. So, mostly it is recommended that you should oil your reciprocating saw 5-10 times a year.
Q: Do you need to oil a reciprocating saw?
A: Yes, you do. To prevent the blade from rusting as well as to keep it functioning smoothly for many years of usage, oil your saw at least once a month or more times depending on how often you use it.
Q: How can I make my Sawzall blade last longer?
A: There are a number of things you can do to make your Sawzall blade last longer. First, always oil it properly every month after using it. Second, make sure that you clean off areas where dust and debris tend to gather such as the pivoting points and rubber grips using canned air or an air compressor. Also, remember to keep your blade covered every time after using it since this will prevent dust from gathering on your blade.
Q: How do you lubricate a Milwaukee Sawzall?
A: To oil a Milwaukee Sawzall saw, first make sure that the blade is not running at high speeds. Second, clean any debris from its teeth using canned air or an air compressor. Third, spray aerosol oil into the blades’ pivot points as well as on both sides of your rubber grips and on any other areas where dust tracks gather. Note that you need to always cover your blade after lubricating it since this will prevent dust from gathering.
2 thoughts on “How To Oil Your Reciprocating Saw Like A Pro”
Comments are closed.