This manual will guide you through the step-by-step procedure of setting up your Dewalt table saw. So, whether you’re a novice or an expert woodworker, you can learn how to set up your DWE7491RS table saw like a champ!
I. How to Set Up a Dewalt Table Saw
First, you’ll have to find a good spot for the table saw. It should be a flat area that’s large enough for you to move around in and accommodate the size of your table saw.
If you’re going to be moving it from place to place, then this is an important step that shouldn’t be overlooked. Unless you’ve got a truly gargantuan workshop, it’s going to be easier to have the table saw in one place and keep your tools nearby.
Once you’ve found a flat spot, assemble the table saw. This means removing all the parts from their packaging and putting them together according how instructions say.
This might sound daunting at first, but it’s actually pretty simple. Once you’ve got the table saw put together, all that’s left is to plug it in and turn it on!
II. Things You’ll Need!
- Screwdriver
- Allen wrench
- Carpenter’s square
III. Step-by-Step Guide to Setting Up Your Dewalt Table Saw
1. Attaching the Rip Fence to the Rails
First, attach the rip fence rail assembly to your table saw by placing it directly above your blade and latching it into place. Once this is done, you can simply align the bottom edge of the fence against your miter slots and check how it runs along the table.
2. Adjusting the Rip Fence
You’ll now need to adjust how far away from your blade it sits by using four screws that you’ll find on one of its sides. Try and place these closer together near the center and further apart as you move towards its edge. Once that’s done, just lock it back into place and you’re good to go!
3. Checking Your Blade Alignment
The easiest way to check how well your blade is aligned with the rip fence is to take a carpenter’s square and see how it lines up with both.
If they perfectly meet, then you’re all set, but if there’s a slight discrepancy, you’ll need to make some adjustments.
To do that, loosen the bolts that hold your saw’s arbour and then spin the blade until it lines up perfectly with both the fence and square.
Once everything is aligned, tighten all bolts back into place and you’re good to go!
4. Adjusting Your Blade Height
This part is pretty simple. All you’ll need is the allen key that came with your table saw and an empty box to store it in.
First, find how many inches above your tabletop your blade needs to sit by turning the elevation crank on its side until you hear a distinct click sound.
This turn of the crank raises or lowers how high up your blade is and you’ll need to know how many inches it’s currently raised.
Once you’ve found how many inches your blade needs to be raised, tighten the lock nut on its top so it can’t turn anymore.
Then, count how many turns of the crank it took for the blade to go up that amount and then turn the allen key that many times.
Don’t worry if you accidentally hit the crank while transporting your table saw, it won’t damage anything!
Also, if you’re worried about how to adjust how high up your blade sits on your DWE7491RS table saw , don’t be. It’s easy as pie and won’t take more than a few minutes!
5. Adjusting the Miter Gauge
Like how you adjusted how high up your blade is on the table, loosen the lock nut on how far away from its edge it sits. Then, count how many turns it took for your miter gauge to move a distance equal to how many inches you want it to be off.
Next, turn the allen key that many times and tighten everything back into place.
6. Putting on Your Push Sticks
If you’re taking extra steps to be safe when using your table saw by putting on push sticks then use the slot just beside the blade and attach them with a screw that’s also provided by Dewalt.
7. Connecting Your Rip Fence and Miter Gauge
This part will only take a few minutes and is actually pretty simple in how it works. Basically, you attach the miter gauge to your rip fence with just a single screw which lets you use them simultaneously or individually for whatever purpose!
You’ve now got your DWE7491RS set up and ready to go on how you need it. It might take a few tries at first, but you’ll be an old pro in no time!
Conclusion & Resources
This guide should have provided you with a set up process for how to how to set up dewalt table saw DWE7491RS and how to use it safely and effectively!
The capabilities of how to use your new table saw are now completely up to you, so go out there and make something amazing.
When it comes to how to set up dewalt table saw DWE7491RS , not everyone has the knowledge or patience to do it, but with this guide you’ll get your project done like a pro in minimum time!
F & Q’s
How do you reset a DeWalt table saw?
Remove the power source and then turn off the saw. Wait a few seconds before reconnecting the saw and resuming your job. Even so, the problem persisted, so consult your user handbook to learn how to restart your DeWalt table. If necessary, you’ll need to buy a new one.
Does Dewalt table saw have a reset button?
There is no reset button on a DeWalt table saw. To reset your DeWalt table saw, turn it off and then back on after few minutes.
Can you buy Dewalt 7491 without stand?
The DWE7491RS is a unique product offering that includes a stand, so the component number would be different if you purchase the saw without one. You would need to purchase the DWE7499GD instead.
Can you use a dado blade on a Dewalt dwe7491?
The DeWalt version can handle an 8-inch dado blade and has a width of up to 13/16 of an inch. Furthermore, at a 90-degree angle, this Jobsite table saw can cut 3.125 inches deep, while it will only cut 2.25 inches at a 45-degree angle.